nanaxhz.blogg.se

18 Februari 2022 - 20:04
Difference between vag tacho 2.5 and 3.01
Allmänt
Difference between vag tacho 2.5 and 3.01











  1. #Difference between vag tacho 2.5 and 3.01 how to#
  2. #Difference between vag tacho 2.5 and 3.01 drivers#
  3. #Difference between vag tacho 2.5 and 3.01 software#
  4. #Difference between vag tacho 2.5 and 3.01 code#
  5. #Difference between vag tacho 2.5 and 3.01 Pc#

This can allow of user to investigate and diagnosis some new units untouchable for remaining diagnostic tools. ĭiagnostic via CAN and Special functions via K-line.Ĭovers all electronic control units in vehicles (diagnostic addresses from 0x01 to 0x80). There is some very important information in eeprom memory of this types kombiinstruments.Filter the km synchronization command between the cluster and the EZS module.

#Difference between vag tacho 2.5 and 3.01 software#

The authors of this software has no ability to test all existing types and models of kombiinstruments, and therefore there is no any guarantee that desired actions will be executed. This software may not works on some types kombiinstruments.Īlso some automated functions also may not be executed due to variety of types and software versions. If error message continue to appear on screen, this means that there are some fatal error, or kombiinstrument or ECU is unknown or program can't log in.

  • Error Messages - In case of receiving any error message, user can try to repeat same operation again.
  • Clear ECU errors - This command will erase all trouble codes that are stored in ECU memory.
  • View memory buffer - This will show memory data on screen in another window.
  • Disconnect - End of communication command.

    • #Difference between vag tacho 2.5 and 3.01 code#

    Note: If you have read PIN code before this procedure, you have to disconnect, turn OFF ignition, then ON and connect again with "Connect Any tacho" for tacho, or "Connect selected ECU" for immo box. The number of all programmed keys must be greater than zero, otherwise there are some error. Then press OK, and read messages from software. User must enter correct PIN code, and number of new keys to program.

  • Program New Key - This will open a new window.
    • User can save whole eeprom data to a file. It is useful if program is logged in to the tacho, but can't read PIN code automatically.
  • Read eeprom - This will read ECU eeprom memory and store data into memory buffer.
    • Not all commands can be stopped, it is useful only for some of them.
  • Stop Action - Pressing this button will cancel any command that is in progress.
  • Change Mileage - This will change mileage counter on kombi display.Īfter pressing, program will try to read actual mileage, then user may enter 'new' mileage and press 'Continue' button.įor some kombiinstruments, it is required to disconnect and reconnect car battery after this procedure.
    • If the operation was successful, PIN code will be shown on display.
  • Read PIN Program will try to read PIN code for log in to the selected ECU.
    • Press it twice to read whole information.
  • Read Info - After pressing this button, program will shows ECU info.
  • Connect Selected ECU - By pressing this button user will connects kombi or immo box which is selected from menu.
    • This is useful when type of kombi is unknown.
  • Connect Any Tacho button - By pressing this button user can connects to kombi, and read info for any car's kombiinstrument.
  • File - User can save and read files to / from program memory buffer.
    • Works only for Immo1 type immobilizers! ) It is useful only if you have an already working key, and switch ignition ON with this key. * (There is selections for VW / Seat / Skoda immo box.
  • Select ECU from Menu - This option selects type of ECU that user will try to connect.
  • After successful procedure, all useful buttons on screen will be enabled.
  • If everything is OK after 5 seconds you will see kombi info on display and program will try to log in to the ECU.
  • After selecting ECU, press "Connect Selected ECU" button.
    • There is no problem if you do wrong selection, but all other functions will work only if you select right ECU.
  • Then press disconnect, and select appropriate ECU from menu.
  • Program will try to connects any kombi and will display type of kombiinstrument.
  • If you don't know type of kombiinstrument, press 'Connect Any Tacho' button.

    • #Difference between vag tacho 2.5 and 3.01 Pc#

  • Connect hardware interface to any free USB port of your PC or laptop.
  • Connect OBD connector to car diagnostic socket.

    • #Difference between vag tacho 2.5 and 3.01 how to#

    Please disconnect your PC or laptop from Internet before install drivers!ĭon't use Windows 'original' drivers! This is important! How to work with software

    #Difference between vag tacho 2.5 and 3.01 drivers#

    Please use only drivers that are supplied with this product. Please stop your Antivirus software before you extract the filesĬaution: This hardware interface requires drivers installation to work!

  • If Windows ask you for a file with extension ".cat", press "Skip File"!.
  • Show Windows where the drivers are on your hard disk.
  • This will start Windows procedure to install drivers for new hardware found.
  • Connect OBD interface to any free USB port.













    • Difference between vag tacho 2.5 and 3.01
    0 kommentar(er)
    Om Mig: